Central Water Chiller : Air-Cooled
Model: TI-100A
Specifications
Have A Question?
Call 317-887-0729
for your answer.
Call 317-887-0729
for your answer.
--
PRODUCT SPECIFICATIONS
Model: TI-100A (1)
Refrigerant Zones
Quantity:
2
Compressor
Quantity:
4
HP:
25
Type:
Scroll
(2) Total Capacity:
93.8 Tons
Refrigerant
Type:
R-410A
Process Pump
HP:
15
GPM:
300
PSI:
60
(3)(4) Evaporator Pump
HP:
5
GPM:
225
Reservoir Capacity
Operating:
1,200 gal
Holding:
1,475 gal
Connection Sizes
To Process:
4"
From Process:
4"
Water Make-Up:
1-1/2"
Overflow:
4"
(5)(6) Full Load Amperage
230/3/60
418.0
460/3/60
209.0
575/3/60
169.0
Dimensions
Height:
112"
Width:
136"
Depth:
128"
Weight
(9) Shipping:
6,505 lbs
Operating:
17,705 lbs
Air-Cooled Condenser
(8) Quantity
Number Of Units:
1
(9) Connections
Liquid:
2-5/8"
Hot Gas:
2-1/8"
(10) Air Flow
Fans Per Unit:
8
(11) Full Load Amperage
230/3/60
52.8
460/3/60
24.8
575/3/60
20.0
Dimensions
Height:
49"
Width:
88"
Depth:
243"
(12) Weight
Shipping
3,100 lbs
Specification Notes::
1. Since product innovation and improvement is our constant goal, all features and specifications are subject to change without notice or liability. Selection of certain optional features may change listed specifications.2. Tons capacity at 12,000 BTU/ton per hour @ 50°F LWT @ 115°F condensing temperature. Capacities may be +/5% as reserved by the compressor manufacturer. Capacity multipliers are 50°F - 1.00 ; 40°F - .80 ; 30°F - .60 ; 20°F - .40.
3. Consult pump curve for exact pump performance.
4. Selection of optional pumps for higher flow rates will raise the minimum recommended operating temperature when no glycol is used.
5. Full load amps are higher than run load amps and must be used for sizing disconnects and supply wiring. Not for construction. Consult factory for power requirements of unit as configured and on selected options.
6. Consult factory for 50HZ operation.
7. Unit weight crated for shipment. Air-cooled units shipped in two units. Basic field assembly required for Air-cooled units.
8. Specifications are shown for a single unit. Some models use multiple condenser units. Field charging required.
9. Field installation including piping connection and charging of remote air-cooled condenser by owner. Process connections may vary based on unique pump flow requirements of your process. Confirm you connection size requirement with your Advantage sales representative.
10. Vertical discharge from condenser.
11. Full load amperage shown for single condenser unit. Some models use multiple condenser units.
12. Unit weight crated for shipment. Condenser unit shipped separately from chiller unit.
13. See Product Warranty Statement W-700 for details on warranty.
TI-100A shown (typical).
Image shown is typical. Actual unit appearance will vary according to specifications and options.
Advantage Engineering, Inc. 525 East Stop 18 Road, Greenwood, IN 46142 Phone: 317-887-0729 Fax: 317-881-1277
Privacy Statement: we will not sell, rent or release any personal information you share with us to third party vendors. Sitemap
Product innovation and improvement is our constant goal. All features, specifications and pricing are subject to change without notice or liability.
Products are assembled in the United States of America.
Privacy Statement: we will not sell, rent or release any personal information you share with us to third party vendors. Sitemap
Product innovation and improvement is our constant goal. All features, specifications and pricing are subject to change without notice or liability.
Products are assembled in the United States of America.
© 2013 ADVANTAGE ENGINEERING, INC
Advantage Engineering Provides Industry Process Cooling Equipment For Optimizing Your Process